AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |
Back to Blog
Clover efi bootloader majave12/27/2023 MSR 0圎2 is locked by the Lenovo UEFI and a KP happens when macOS attempts to set it: The Clover patch nullifies such attempts Clover to update their built in "KernelPm" patch.While it's not really a huge issue, we will forever be at the mercy of the developers behind the following software: Whilst Lenovo finally got rid of their/IBM's terrible Wi-Fi card whitelist, meaning that one can now switch out the Intel Wi-Fi card (which I do think is better than the DW1830), the UEFI remains locked nevertheless.FakeSMC does however have the advantage that it can display the fan speed with ACPISensors (if the right part in SSDT-BATT.dsl is uncommented and the DSDT rebuilt). Even the Lenovo UEFI won't reset your settings, but with FakeSMC (or perhaps Clover's SMCHelper-64.efi driver) a hang would occur at the point before Clover could hand over booting to the macOS kernel. This write-up uses VirtualSMC instead of the venerable FakeSMC as the former is more resilient if the CMOS checksum gets invalidated.If you do get either working, and changes to the files in this repo were needed in order to do so, please consider creating a PR. I don't believe Mojave supports VGA out, and I've never tested the MiniDP.I'm hoping that this is because of me running my laptop at 1680×944 (3360×1888 "Retina"/HiDPI), setting battery thresholds on already-old batteries and not allowing the audio chip to go into power saving mode when headphones are plugged in So, yeah, update your Clover before macOS! 4 to support kext loading from outside of the standard locations. Newer versions of Clover had already had updated the patch targets for. Long story short, it was because WhateverGreen wasn't being loaded as my Clover version was too old. 4, I was getting a kernel panic and I wasn't able to see why because of irrelevant information being dumped to the screen. Something that I was unaware of while updating is that loading kexts from Clover's EFI folder (as opposed to /Library/Extensions etc.) is only possible because Clover hot patches some component to allow this to happen.Dark mode is far too enticing for me to test anything else. I have only tested this X250 with 10.14.3, 10.14.4 (updated from.Problems and other things you should be aware of Sinetek's driver (recommended: syscl's fork) might work somewhat I have not tested it personally I personally enable TRIM by running sudo trimforce enable, but some schools of thought say it's not needed when using APFS If your X250 has a WWAN card, then the DW1830 probably isn't the best choice as the DW1830 has three antenna ports - I use one of the WWAN antennas for the Wi-Fi card The TrackPoint, with VoodooPS2Controller, also works should you feel more inclined to use that instead No idea if it actually works, but it shows up fine and Mieze's driver is well tested at this point in time The original Intel 7265 (with BT) was replaced, as it's not supported by macOSĪirDropping to and from an iPad 4 works fine Speakers and headphone output works, as long as the modified ALCPlugFix is installed Not touchscreen, and brightness control works in Windows Make sure to read the CPUFriend short note later on in this write-up You'll then be missing the few QOL tweaks in this guide, however. The TL DR version of this is something along the lines of use the SSDTs from here, grab the ist from here, install Clover with the drivers I mention and install the kexts I mention. While it does undeniably make things easier, I don't want to be distributing old versions of software, and nor do I want the responsibility of keeping this repository up to date with every kext etc. I do not keep a complete EFI folder here. Only 2 x USB 3.0 ports by RENESAS UPD720202 not working.Otherwise, you'll be missing a ton of files. Note: EFI is only tested on Mojave but should work with Catalina and might work on Big Sur. Voila you will be booted into MacOS, now you may setup your Hackintosh. (It is suggested to install MacOS first if you are going to dual boot it with Windows) Let it boot, Create desired partition through disk utility APFS format. Boot Into USB to get installation started.Įverything is Predefined you do not need to make any changes in Clover.Ģ. Run Explorer++ as administrator replace clover files with H81i Clover filesģ. Assign letter to EFI USB partition so that windows can recognize it.ĥ. Download Explorer++ and Mini Tool partition wizardĤ. Set IGD to PEG if you are going to use RX580 otherwise IGD is fine.ģ. Enable Windows 8.1 feature, disable secure boot.ģ. In order to get the installation started you will have to configure biosĢ. This guide is meant for the following build
0 Comments
Read More
Leave a Reply. |